ink pumps

Showing 1–12 of 13 results

  • Graymills Double Diaphragm Ink Pumps

    For applications requiring controlled flow rates from a trickle to 40 gallons per minute. Especially suited to the requirements of bottom printing corrugated lines, where a single pump provides both supply and suction return.

    These pumps operate by the movement of two flexible diaphragms which move back and forth, alternately filling and emptying two chambers. Flow is controlled with the air inlet valve, which then determines pump speed. A variety of applications are possible because the pump’s inlets and outlets can be configured in different ways, such as “one-in one-out”, “1-to-1”, “two-in two-out”, or “2-to-2”. In the 1–to-1 option, one color is sent to the deck. In the “ 2-to-2” configuration, you can deliver one material and also draw it back, or deliver two inks to two different decks. Diaphragm pumps do have a pulsating flow and are best use with a Graymills surge suppressor/filter.

    Read More
  • Graymills Dual Head Pumps

    Two peristaltic pump heads powered by a single motor allow the pump’s heads to be individually set to supply or return. This ability, coupled with the pump’s variable speed capability and ability to reverse direction, allows for several pumping configurations:

    • Supply one ink to two separate decks
    • Supply two different  inks to two separate decks
    • Supply and return one ink to one deck

    These pumps are available in PPS or PPL versions, have standard quick change heads, eight position adjustable head orientations, and remote mounting of controls with a 16’4” (5m) cord. Available with electric gear motor with electronic variable speed control; consult factory for explosion proof model. CE compliant models available.  Optional hard coat anodized head with stainless steel rotors (PQL only).

     

    Read More
  • Graymills H2000 Series

    Centrifugal Ink Pump

    Centrifugal pump for use on narrow web, tape, tag, label, envelope, and smaller specialty presses. Tri-rod construction and Teflon coating for easy clean–up. Optional Quick Demountable motor. ATEX and CE compliant models available. High speed version, H2000H series, can be used for lifting heavier viscosity liquids to higher print decks and into chambered doctor blade systems that require more pressure. The H200H series delivers higher flow for top performance – for use on mid size flexographic and rotogravure presses. Fits in 2, 5, 10, 20, and 30 gallon containers in standard or stainless steel.

     

    Read More
  • Graymills H3000 Series

    Centrifugal Ink Pumps

    Centrifugal pump for use on mid and wide web flexo and gravure applications, especially those requiring more flow and/or higher print decks. Tri-rod construction and Teflon coating for easy clean-up. Optional Quick Demountable motor. ATEX and CE compliant models available. Fits in 5, 10, 20, and 30 gallon standard steel or stainless steel tanks.

     

    Read More
  • Graymills H4000 Series

    Centrifugal Ink Pumps

    Centrifugal pump for high flow, high decks, on flexo, and gravure webs over 60 inches (1.5m) wide. For viscosities exceeding 40 sec. use either a 3/4hp electric motor or #4 air motor. Optional Quick Demountable motor. ATEX and CE compliant models available. Fits in 10, 20, and 30 gallon tanks.

    Read More
  • Graymills HR series

    Centrifugal Ink Pumps

    Centrifugal pump for use on larger narrow web and envelope presses requiring flow rates up to 2 GPM and viscosities up 30 sec. No.2 Zahn. These pumps are constructed of a Teflon® coated cast iron body, stainless steel shaft, ½” NPT discharge, and agitor tube for in-tank circulation. Fits in 2 gallon stainless steel tank with nickel plated lid. Non-explosion-proof, explosion-proof, and air motor options.

    Read More
  • Graymills HV series

    Centrifugal Ink Pumps

    Centrifugal pump for use on small presses requiring flow rates of less than 1 GPM and viscosities up to 30 sec. No.2 Zahn. These pumps have a high strength thermoplastic pump body, stainless steel shaft, ½” NPT discharge tube, and agitor jet for in-tank circulation. Available in 1 or 2 gallon tank size. Non-explosion-proof, explosion-proof, and air motor options.

    Read More
  • Graymills Ink Pump Mixers

    Take variables out of your printing process. Keep your color and viscosity more consistent with a full line of mixers from Graymills. These in-tank mixers keep inks properly blended, which is especially important for users of diaphragm or peristaltic pumps.

    Small tank mixers fit 2 and 5 gallon containers. They are available with air motors. Can be mounted to optional lid. Also available to fit in 10, 20 and 30 gallon round tanks.

    Mixers for 55 gallon drums are available side or lid mounted. These mixers use piston-powered air motors that run steadily at low RPM for gentler mixing, using less air and reducing noise. These mixers are designed to assure mixing throughout the container, even into corners, eliminating dead spots and changes in viscosity or color density. Most units are also available with traditional vane-style motors, which provide higher mixing speeds.

    Read More
  • Graymills MegaMag™ Filter Magnets

    For Superior protection against anilox scoring/damage.

    A rare earth magnet in a smooth stainless steel casing, with 10x the pulling power of a standard magnet; megaMAG™ is able to attract metal particles from within the filter body or ink tank. Unlike other rare earth magnets, megaMAG’s domed end design with no crevices releases particles easily when cleaning.

    megaMAG™ is available for use in Graymills Superflo® filters HFST and HFNT or on an adjustable bracket (C-37327 or mini-megaMag bracket C-38745) for placing inside a tank or pail. Also available for use in DDFSFST and DDPSFNT surge suppressor filters. Retrofits to all existing Superflo® filters and surge suppressors.

    Read More
  • Graymills PPL Ink Pumps

    For mid to wide web flexo, gravure, and rotary screen applications and light to heavy viscosity inks, coatings and adhesives (including UV/EB), requiring flow rates of 4.5 GPM or less. Available with electric gear motor with electronic variable speed control (115/230 VAC) 50/60 Hz or ATEX electric gear motor with variable speed control (230/460 VAC, 3 Ph) 50/60 Hz.

    Optional “Quick Change” removable head Model PQL. Pump head/tube changes are accomplished in seconds without tools. Simply pull the lock-pin, remove the used head, and replace with another head loaded with clean tube. PQL models include all of the features of the standard PPL models. “Quick Change” heads can be retrofit to Graymills peristaltic pumps made since January 2005.

     

    Read More
  • Graymills PPS Ink Pumps

    For narrow web flexo and rotary screen applications, and light to heavy viscosity inks, coatings, and adhesives (including UV/EB), requiring flow rates of 1.5 GPM or less. If flow requirements are above 1 GPM, consider model PPL for slower running speed and longer tube life. Available with electric gear motor with electronic variable speed control (115/230 VAC) 50/60 Hz electric gear motor or variable speed air gear motor (28 CFM@80psig/792.9 LPM @ 5.4 bar).

     

    Read More
  • Graymills PQLM Ink Pumps

    Model PQLM is the model for tough environments. This metal head version of the PQL lasts through long runs, numerous changeovers, and demanding applications. Variable speed control offers adjustable flows which can exceed 4 GPM.

     

    Read More